Jump to content

Recommended Posts

Posted

speek to Kev mate KJ hes good on the nitrous systems but in your v8 you could run that easy as its only 25 per cylinder which is fook all,will be a kick in the ass Brett :lol::lol::thumbsup:

Posted

trying to get it sorted at the mo money is very tight got the inlet fitted with nos jets but i think a fogger plate kit would be a better option as it would be a lot easier to plumb in have you put any in yours

Posted

Running a dog's boolcks Cold fusion system fitted by KJ, kick's in when full throttle position is reached, on board computer sorts ramp time etc, ignition retards 4 deg when system is armed, gained .7 of a second so far with 35 hp jets, moving up to 60's for round 6!

Posted
trying to get it sorted at the mo money is very tight got the inlet fitted with nos jets but i think a fogger plate kit would be a better option as it would be a lot easier to plumb in have you put any in yours

 

No im not using gas at the moment ,but will do maybe next year but i will only probably run 30 shot as engine will be maxed out,well crank will :lol: if you use the plate so its direct port it will work so much better and the power and torque will be alot more than a fogger in the inlet,but both will work ,its just you need to make sure you get the fueling spot on ,,,,,as said Kev is the best person to advise you :thumbsup:

Posted
delta how are you retarding the timing msd unit ? terry you are doing well if the cranks on its limit

 

The retard is done through the DTA management system. as is the rev limeter (8,000 rpm)

Posted

well they say standard cossie crank is good for 700hp and i think if i ran a 50 or bigger i would be around that figure,but then i could allways test the theory :lol: but it becomes expensive when things go wrong

Posted
well they say standard cossie crank is good for 700hp and i think if i ran a 50 or bigger i would be around that figure,but then i could allways test the theory :lol: but it becomes expensive when things go wrong

 

I'm running Arrow crank and rod's, with JE forged pistons, Ferrera valves, should be good for a bit!

Posted
speek to Kev mate KJ hes good on the nitrous systems but in your v8 you could run that easy as its only 25 per cylinder which is fook all,will be a kick in the ass Brett :lol::lol::thumbsup:

 

You've confused me Terry :?

 

I always thought a 200bhp shot of nos is 200bhp per cylinder, not divided by the amount of cylinders. i.e - if you were running a 50 shot, that would be 50 to each cylinder, not 12.5 to each :?

Posted
speek to Kev mate KJ hes good on the nitrous systems but in your v8 you could run that easy as its only 25 per cylinder which is fook all,will be a kick in the ass Brett :lol::lol::thumbsup:

 

You've confused me Terry :?

 

I always thought a 200bhp shot of nos is 200bhp per cylinder, not divided by the amount of cylinders. i.e - if you were running a 50 shot, that would be 50 to each cylinder, not 12.5 to each :?

 

 

that would equate to 1600bhp in a V8.... doubt thats possible ! :lol: bet it would be funt though !

 

 

(And Steves shot would be 300bhp worth.. which i doubt a na cossy would take - ontop of what it has already)

Posted

No, I don't mean added together, I just mean 50 or 200 or whatever is the total increase. So malcy will run 65bhp total next round. I told you i was confused :lol:

Posted

ok i will put it this way if you put 100 shot jet in on a 4 cylinder it will equate to 25 shot per cylinder simple maths,on and N/a you normally will see somewhere around that figure in horse power,but more torque,on a turbo car if you ran 100 shot depending on size of turbo ,your 100 shot could see you with an extra 130 to 150hp and a shit load more torque

 

Malcy giz your arrow crank jammy bugger :mrgreen:

Posted
trying to get it sorted at the mo money is very tight got the inlet fitted with nos jets but i think a fogger plate kit would be a better option as it would be a lot easier to plumb in have you put any in yours

 

If you run seperate foggers, ie one per inlet runner on a v8,you will

 

make a lot more bhp than a plate kit but you will need a much bigger set of

 

solenoids to flow more gas/fuel , just depends how much bhp your motor

 

could take ?

 

You could easily put in a 200 shot of gas with seperate foggers .

 

I run an msd digital 6 system on my car which will back out up to

 

10 degrees of ignition if you want it to.

 

puddy :thumbsup:

Posted

got an msd ignition and a plug in timing retard but i havent fitted yet got the dirrect port system already plumbed in but the pipe work is a mission and and the new plate system im after is a bit special

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...