Jump to content

Recommended Posts

Posted

So I went out to fit my new Accuspark dizzy today (I've already fitted the blue coil, leads & plugs.), but I've got myself in a right pickle. I'm hoping that you can help me make sense of it.

 

The Capri is a proper mongrel - Mk3 running gear in a Mk1, with the electrics chopped (from I think what was originally a Mk1 loom)  to suit. It's a Bosch dizzy that has had a Powerspark unit fitted for the last couple of years. It currently looks like this.

 

CapIgnition_zpsa16f1a96.jpg

 

 

Given that I've got a brand new multi meter, I thought I better check the voltage at the coil to check that it is ballasted. I followed Accuspark's instrcutions

 

Testing for a ballast resistor or wire

If there is no ballast resistor visible you may have a ballast wire inside the loom. To test for it proceed as follows:
1. Check voltage of battery with volt meter and make a note
2. Remove the wires from the negative side of the coil (negative earth cars)
3. Connect a temporary wire from the negative terminal of the coil to earth
4. Turn ignition on (nothing else switched on)
5. Now chec
k the voltage on the coil, put red probe on + side of coil and the - probe to earth
6. If the reading is less than 80% of battery voltage there is probably a resistor in the system. If it is more than 80% you probably have a standard system
7. Remove the temporary wire and reconnect wires.
If your reading is less than 80% you should use a ballast coil, or our AccuSpark Blue
If you reading is more than 80% you should use a non-ballast coil, or our AccuSpark Red

 

 

But I was unable to get any voltage reading at Stage 5.

 

Then I tried the method on this Youtube Video

 

http://www.youtube.com/watch?v=pWxJmbm5V3s

 

This gave me a reading of 12v, which suggests that my ignition is set up without ballast. What's thrown me is that, prior to changing the coil over to the Accuspark blue a couple of weeks ago, the car ran fine for years on a coil marked "non-ballast".

 

I'd really appreciate your thoughts on this......

 

Is there anything wrong with the way I tested this?

Given the above info, does this seem like a non-ballast system to you too?

Is there anything else I can check to be sure either way?

 

Your help is much appreciated

 

Cheers,

Jim

 

 

 

 

 

 

 

 

 

Posted

Jimbo, electrics can be a nightmare, but assuming you have a negative earth system and all your components are designed for negative earth cars then usually there is a simple answer somewhere. Have you re-checked the installation instructions for your equipment? I'm not familiar with the Accuspark system and i'm not sure how representative your schematic is supposed to be, but in a normal negative earth system isn't the coil negative the connection that usually runs to the distributor?

 

If the problem is not immediately obvious, i'd suggest retracing all your steps and starting again from scratch. I'd probably start by disconnecting everything you installed since the car was running OK, i,e. without the coil and distributor connected. If you're not getting voltage on step 5 then you might have blown a fuse. Check you are getting a voltage on your ignition wire feeding the coil and go from there. Don't discount having a faulty coil either.

Posted

Did you put the earth to the other side of the coil as it states ?

 

The only reason for no volts is either no power or no earth to the coil.

Posted

Thanks chaps for the replies.

 

Sorry, Sorry, Sorry!!  I think that my original post wasn't clear - not the first time, eh Savvi?

 

Perhaps a few more things I should have explained.

 

The car is negative earth

The car is currently working with the above wiring config, and with the Accuspark blue (ballast coil) fitted.

 

The old coil has a very faded label, which I though said non-ballast on it. I've just run the digimeter on the old coil, which reads 1.5  Ohms suggesting that it is actually a ballast coil. However, all that would suggest that I should only expect 9v being fed to the +ve side of the dizzy, yes?

 

There's every chance it's me being stupid. I'll recheck on Tuesday.

 

Just to clarify, On Step 4 : Turn ignition on (nothing else switched on) That means in Position II, with ignition light on and engine not running, yes?

 

Cheers again,

Jim

Posted

I stopped by Accuspark HQ to pick up an alternator, and the chap had a quick look at the car.

 

The obvious thing he pointed out was that the LT wires were the wrong way around, so now it looks like this.

 

CapIgn_zps433f2609.jpg

 

 

I've tidied up the colour coding on here as well now.

 

So that leaves me with two questions

 

1) The red wire that comes from the dizzy should connect to the the live feed before the ballast, that means my current powerspark set up  is wired incorrectly, yes?

 

2) If I want to get my tacho working, it should be taking a feed from the negative pole on the coil.  Currently the yellow / white  goes into the loom in the engine bay. I get continuity to the Pink / White that comes out of the loom behind the dash. This agrees with the Haynes manual. A bullet connector joins it to a white wire, which then runs though a pickup / induction loop on the back of the tacho. Haynes agrees with this too.

 

Where I get confused is.....

 

On my car the white wire runs for a few centimetres more, before it connects to a spade terminal on the back of the instrument cluster. It looks like it's going to earth.

 

However, the Haynes manual shows the white wire running all the way back to the ignition switch. Here it joins with another white wire that leads to the brake light switch and the heater. The brake light switch then obviously runs to the lights and then earth, the heater wire runs to the heater (the side opposite the two-speed heater switch / resistor setup. This looks like +ve feeds to my untrained eye

 

My question is, having run through the pickup on the back of the tacho, should that wire just run to Earth?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...