Jump to content

Recommended Posts

Posted

i've just buggered up my other computer :sad: my case was broken so i got a new case and tryed to swap everything over, now its just a mess of wires and doesnt work :sad:

so if anybody would be able to help me out ASAP as i use it for OSF and college work (all my college work is still on it) it would be greatly appreciated :wink: and payed well in beer and love :kiss:

Posted

does it power up at all? i.e. fans spin etc?

 

i reckon the most common thing to miss is a 4 pin power extension depending on the age of it. its 2 yellow and 2 black wires.

Posted

make sure u got the ribbon cables the right way round,ie one edge of the cable has line on it,thats no1.look at the drives+m/b will be marked where no1 is,match em up.

 

look 4 a thin wire marked sw(switch wire)is in the right place

Posted

ok, at the bottom of the case are there about 10 very tiny wires that plug onto the motherboard. these are usually speaker, power button, reset button,power LED, hard disk LED. are these all plugged in the right place? if your not sure, take them all off, and run a small electrical screwdriver along them, touching all the points (CAREFULLY!) :lol:

 

this should 'bump' start it.

 

icant really get pics cos i'm not at work, ad i'm not takig mine apart, cant be arsed :lol:

Posted

orionmojo, it has a 4 pin plug but before i took it apart i noted all the plugs that were not attached to anything - that was one of them :sad: i tryed running a screwdriver along the pins but to no avail.

 

there just seems to be a lack of power to the motherboard ATM :?

Posted
i've just buggered up my other computer :sad: my case was broken so i got a new case and tryed to swap everything over, now its just a mess of wires and doesnt work :sad:

so if anybody would be able to help me out ASAP as i use it for OSF and college work (all my college work is still on it) it would be greatly appreciated :wink: and payed well in beer and love :kiss:

 

take a photo of what its not plugged in.

 

sounds like your power switch might not be connected.

 

I'm in nottingham, but would be more than happy to help :)

Posted

i cannot see ANYWHERE for it to go :? it wasnt connected when i took the computer apart (and it was working fine) its just annoying cos its gonna be something stupid :lol:

Posted

ignore my above post, it wont help you as you dont need p4 connectors

 

computerbits004.jpg

 

Try to unplug the grey leads to the left of this photos - USB connections. try booting then

 

Jon :)

Posted

grey leads removed but still no luck :sad: , i plug the power in no lights/fans etc come on, its like theres no power to the whole system

i've swapped the power leads and its not a problem with them, could a fuse be gone in the power suplly area? :?

Posted

It could be the PSU (power supply) thought not likley.

 

Have you tried a different PSU lead? - kettle lead

 

EDIT - sorry you say you have done the above!

 

Its really hard to make head or tail of it without being there sorry :(

Posted

Ok im about to goto bed (early i know!)

 

but

 

please confirm you are using the same power supply, mother board and other components in this case as you were the other case...

 

Also It could be the mother board is touching the new case and shorting out - small but possible chance.

 

right heading to bed will try again in the morning

 

Thanks

 

J

Posted

thanks for all your help m8, its annoying cos theres nothing more i can thing of to do, the leads have been changed but the fan did just do half a spin ! :D

Posted

Wessie mate bring it round to mine...i have a spare PSU etc and can take a look for ya.....grab me on MSN or get my moby number from Marty..i'm in Guildford as well...

Posted

if the ans are spinning its not the PSU.

 

take the graphics card out, and the tv card. then reseat the graphics card leaving the tv card out.

i can see from the picture that they dont meet the care properly at the top. if te motherboard screwed in? it could be shorting out if its ot, and you'll probably have knackered it.

 

did you earth yourself before you took it out? and did you hold it by the processors heatsink? this is the best way to prevent killing them 'in transit' cos they're well sensative to static.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...