Jump to content

Recommended Posts

Posted

ok thanks to duchy boy Mark (top bloke) i got meself a good (running nicely) 205 2.0 pinto motor, dunno wether to fit it now and use it for rest of summer or do the biz on it now and fit it in winter, all i wanna do is put a mild cam in it and paint it up and powder coat brackets etc, can anyone suggest a suitable cam for me, i wont be tracking it , but i do like to boot it round the local country roads, i prefer acceleration to top end , also my pet hate is a lumpy tickover ..

any other suggesstions on mild tuning welcome but please consider i reallly dont have a lot of money to play with just yet (got 2 grandkids on way and my son is gettin married so my moneys tight)

im soooo excited :mrgreen:

 

(excited about me new engine, not grandkids :roll: )

Posted

Got to be the Piper 270 cam for best all round with smooth tickover.

 

That alone with a K&N and a decent exhaust manifold & system should see 120bhp ish. Just don't forget the vernier :oops:

Posted

a vernier is an adjustable top pulley that replaces the standard one. It's essential to fit one when you upgrade the cam to allow you to 'dial' the cam timing in accurately. They will do it when you have it run up on the rolling road.

 

As for exhaust, I've always been skint so have used ashley stuff but if i had a bit more money, I would go with Janspeed. (Unless I was REALLY flush, then I would have a Tony Law manifold :mrgreen: )

Posted

Rally cams are good - I had a RL32 in my old pinto, very torquey, idle was fine. 2" Ashley 3-2-1 fit fine and cost effective...

Posted

Lots of cars with lumpy idles are the result of incorrect carb' settings - the old 3 litre dgas on a 2 litre pinto for example. If set up properly almost any cam will idle well. Too rich mixture will make it idle rough / lumpy.

Posted

i have a piper BP285 in mine, its pretty poor off the rev range, it will sit at about 1,500 which is 30 in 4th ok, anythin lower and it will judder a little, but this may be my carb, but as you get up into the power band, starts at 2250rpm it doesnt half shift!!!

Posted

problem is no-one lists a competition exhaust for a MK1 capri, its all MK2 & 3 .

 

i suppose the manifold listed for 2.0 pinto will fit any car? do they make that much difference to a stock engine?

and the vernier pulleys , are they crucial when fitting a bigger cam? i dont want to get too far ahead of myself, specially when everyones telling me that just changing from a stock 1600 to stock 2000 will be a remarkable difference in power.

Posted

you will get a noticable gain, but if you want to put a different cam in you will need a vernier, the manifold will make a bit of difference to a standard engine, but only really significant on a modified engine

Posted

A book is a great idea, then spend a few quid on the head and cam, this way you can get a really good engine built up and you can add an exhaust or twin carbs later when funds allow. I think a standard 2.0 will be better than a 1.6 but a head and cam will make it the "sporty" drive you're after.

 

For what it's worth "Tuning the A series" (Seriously) is my bible, I think Vizard is great and this book really explains stuff from the basics of explaining how air and petrol is turned into power, right through to cam overlap, lca, choosing carbs, flow tests etc etc. :thumbsup: Buy it!

  • Admin
Posted
i see theres a pinto tuning book on the market, has anyone read it? or better still dya wanna lend it to me :roll:

 

I have it in pdf if you want me to email it to you, it's quite a large file size though.

Posted

Before you touch the engine id stick it in. Theres no need to remove it unless your working on the bottom end and as your plans arent too big, once its in, its in. You might find it to be enough, and you can enjoy it over the summer :thumbsup:

 

I dont know what cams in mine, only that its very harsh. Ive got a 38dgas and now ive had a go at setting the idle up it ticks over at 650rpm cold, 800-950rpm warm depending on temp. Its not rough at all but its very off beat but thats probably due to my exhaust. It does pull at low revs but struggles until about 2000rpm, then at about 2500rpm it really takes off.

 

I think your best bet is to look at the spec of the cams, see what you think is best, then go down a stage. You want tourque more then power.

 

A good cam, a well set up 38dgas and a good exhaust system and your laughing.

 

I reckon you should get a side exit too.

Posted
i see theres a pinto tuning book on the market, has anyone read it? or better still dya wanna lend it to me :roll:

 

I have it in pdf if you want me to email it to you, it's quite a large file size though.

 

thanks vista but id rather have a book i can take to work and read at breaks, and in bed :thumbsup:

Posted

It really would be rude not to cam it before it goes in, with the engine on the floor its a doddle, can be done in under an hour...

 

the minimum id go for is a piper 285 or kent FR32, nice tickover with usefull midrange power.

 

stick with a 32/36 and 4 branch with system and you have a nice squirty 2 litre that will be pretty good on fuel to boot.

 

ive built engines to that spec that have made 131 at the flywheel, and suited 1600 4 speed box and axle really well.

Posted

 

For what it's worth "Tuning the A series" (Seriously) is my bible, I think Vizard is great and this book really explains stuff from the basics of explaining how air and petrol is turned into power, right through to cam overlap, lca, choosing carbs, flow tests etc etc. :thumbsup: Buy it!

 

YFKT mate...that book is also my bible, i took 4 months to read it, then read it again, i cut me teeth on the a series engine, that book is the tits!

 

ok its not a ford engine, but most of the same rules apply.

Posted
Can I quickly just add that all pintos have a vernier pulley. You will need an adjustable vernier pulley on your new cam :thumbsup:

 

I know it might seem obvious to some, but accurate advice is best ;)

 

learn summat new everyday :shock:

 

i know jack shit about pinto so ill go sit in my corner now :lol:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...