razersedge Posted October 4, 2008 Report Posted October 4, 2008 as some of you know i broke my car last weekend, i have had it jacked up trying to find the damaged part but with no luck, its shaking and shudering about above 40 mph and at 60 i sware the back is jumping off the road when i let off, but i cant find the problem what i thought it was it doesn't seam to be but i can't see what it is that is causing it, the axle is shaking, the prop is shaking, the gearbox is shaking and the body is shaking but i can't see what is causing it so i have made i video of the car jacked up in 4th gear showing all the parts and i'm hopping some one will see some thing i am missing or has had the same problem
flyingbanana Posted October 4, 2008 Report Posted October 4, 2008 have you checked the weights havn't come off the prop...or the prop been taken off then put back 180 degrees out
escort21 Posted October 4, 2008 Report Posted October 4, 2008 Take the prop off and check the uj...if one of the bearings have collasped then itll run off centre and everything will shake
V8ian Posted October 4, 2008 Report Posted October 4, 2008 Looks like there is too much nose down on the diff, that may or may not be a cause of the noise, as Tim has said, drop the prop, and check the prop bearings, see if there are any witness marks to see if the prop has been catching on the UJ, also try putting the car in neutral and turn the prop over by hand and feel for tight spotsif you find a tight ot loose spot around every 4 turns you can guess its the crown wheel with tooth damage, a constant grumbling diff or half shaft bearing, my guess is you have fooked the diff,
countrybumpkin Posted October 4, 2008 Report Posted October 4, 2008 its likly to be the prop but it could also be somthing up with the diff, you may have lost a tooth off one of the diff gears
mrcheese Posted October 4, 2008 Report Posted October 4, 2008 Tell us what the accident was and we might have a better idea of the problem! A couple of quick checks.. try pulling forward and reversing at low speed several times, if you hear an audible clanging its likely that you have damaged a bearing (or is worn) on the prop. Also try drving the car around the 40/50mph mark, if the vibration isn't so bad when your accelerating and worsens when you back off then its very likely a fault with the prop (broken weight / worn or broke bearing) or the diff and gearbox tailshaft at the wrong angle. Your diff looks to be at quite a severe angle but i dont know if its just as the car is jacked on the diff, the best ay to test if the angles are ok is to put the car on stands, 2 stands on the cross member and 2 on the axle (you must make sure that weight of the car is on the axle/ and very important make sure the car is perfectly level) use a builders spirit level across the length of the sills and across the sills side to side. Now get uder the car and using a small spirit level check that the angle off the diff flange is the same as the angle on the front uv joint, they need to be symetrical as if they are out you get what it called the skipping rope effect which is what it sounds like youv'e got. Let us know how you get on
razersedge Posted October 4, 2008 Author Report Posted October 4, 2008 it wasn't an accedent it happened on launch whilst drag racing it's a lot more than lost weight's on the prop the reason i run the car in 4th gear was because i wasn't prepared to get out of the car with it in 5th i'll have a look at the prop tomorrow to see if one of the bearings has gone, the car it self is ok (as well as can be expected with me driving it) and i do hope it's not diff no 4
countrybumpkin Posted October 4, 2008 Report Posted October 4, 2008 if it happend on launch its unlikly to be the prop unless its bent, i'd say it could be a tooth missing off the diff gears or a bearing broken up, or a bent halfshft there is one other thing that i can think of it could be, i have only seen this happen once and it was on a land rover, a broken halfshaft that has caught back up on its self so you still have drive
Copey Posted October 4, 2008 Report Posted October 4, 2008 a broken halfshaft that has caught back up on its self so you still have drive i can imagine that being a freak occurance
countrybumpkin Posted October 4, 2008 Report Posted October 4, 2008 a broken halfshaft that has caught back up on its self so you still have drive i can imagine that being a freak occurance yeah definatly but still possible but it may only be able to happen when you have a fully floating axle i'm not sure but i know no one had ever see it happen before we spent about a hour just looking at it in the workshop before even thinking about putting a new one in
Copey Posted October 4, 2008 Report Posted October 4, 2008 a broken halfshaft that has caught back up on its self so you still have drive i can imagine that being a freak occurance yeah definatly but still possible but it may only be able to happen when you have a fully floating axle i'm not sure but i know no one had ever see it happen before we spent about a hour just looking at it in the workshop before even thinking about putting a new one in haha, so how many of you took pics then? haha
countrybumpkin Posted October 4, 2008 Report Posted October 4, 2008 a broken halfshaft that has caught back up on its self so you still have drive i can imagine that being a freak occurance yeah definatly but still possible but it may only be able to happen when you have a fully floating axle i'm not sure but i know no one had ever see it happen before we spent about a hour just looking at it in the workshop before even thinking about putting a new one in haha, so how many of you took pics then? haha a few of us did (the ones young enough to use a camara phone anyway) i'll see if i can sort out a pic and post it up
razersedge Posted October 4, 2008 Author Report Posted October 4, 2008 it's not a bent drive shaft the shafts were new to that round of racing, one has got a little buckle in it but i had to look hard to see it not like the set i took out which you could see from about 50 ft away it has got an lsd but it's looking more and more like a full strip down "gulp"
davreeve Posted October 4, 2008 Report Posted October 4, 2008 Looked at your vid,difficult to pinpoint,prop looks straight(although diff pinion angle looks a bit out) so looks like an axle stripdown is on the cards good luck with it,hope its not to damaging to your wallet
w p e Posted October 4, 2008 Report Posted October 4, 2008 mike thats a tooth missing on the pinion. been there done that
c20xe Posted October 4, 2008 Report Posted October 4, 2008 Check the clutch pressure plate hasn't got a broken drive strap or the diaphram fingers havn't broken, its also possible that the springs in the clutch plate have broken all these things cause the clutch and pressure plate to run out of balance and cause vibration like you wouldn't believe,because it happened a launch the clutch assembly would be my first port of call.
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now