LEONMEX Posted January 5, 2007 Report Posted January 5, 2007 Went to bolt my bvh to my fresh 2.1 today & 1 of the head bolts snapped I managed to get it out but they have bottomed out on the block,ive run this head on my old engine no probs but the new block has been decked (by a reputable engine builder) & the bolts are about 2-3mm to long now Is it o.k. to use proper head bolt washers or does anyone know where to get the proper bolts.
Admin Vista Posted January 5, 2007 Admin Report Posted January 5, 2007 Is it not possible to shorten the bolts by the amount that's been taken off the block?
LEONMEX Posted January 5, 2007 Author Report Posted January 5, 2007 YKT mate,was hopeing to get it up & running this weekend. Ive got a few people to speak to tomo about some options on the bolts but bit of a pain in the arse. Still got a few stellas to make it better Vistars I tought about cutting the bolts down but would of preffered an easier way round it,but i might end up cutting 5mm off the bolt with my hacksaw.
CéDriC Posted January 5, 2007 Report Posted January 5, 2007 Can't you found high tensile bolt in the size you want depend of the thread...
LEONMEX Posted January 5, 2007 Author Report Posted January 5, 2007 The thread is m12x1.75 & the bolt shank is 92.5mm long the shortest i can get is 80mm which is to short. I think im going to cut down some standard bolts. Just wondered if anyone else had had this prob
Admin Vista Posted January 5, 2007 Admin Report Posted January 5, 2007 By cut down I assume you mean face them off in a lathe? Not sure I'd simply take a hacksaw to them.
LEONMEX Posted January 5, 2007 Author Report Posted January 5, 2007 I did mean with the saw,you dont reckon its a good idea? Ive got an old block to test them on before i put them in. Prop be better in the lathe then? I have got use of one & its only a phone call away,a lathe that is.
CéDriC Posted January 5, 2007 Report Posted January 5, 2007 The thread is m12x1.75 & the bolt shank is 92.5mm long the shortest i can get is 80mm which is to short. I think im going to cut down some standard bolts. Just wondered if anyone else had had this prob Here we can have 80 85 90 or 95 one... Let me known if you have trouble... I could found some at work and send them to you...
Admin Vista Posted January 5, 2007 Admin Report Posted January 5, 2007 better finish, hacksawing them off would introduce stress raisers into the end of the bolt.
LEONMEX Posted January 5, 2007 Author Report Posted January 5, 2007 The thread is m12x1.75 & the bolt shank is 92.5mm long the shortest i can get is 80mm which is to short. I think im going to cut down some standard bolts. Just wondered if anyone else had had this prob Here we can have 80 85 90 or 95 one... Let me known if you have trouble... I could found some at work and send them to you... Brilliant thanks very much,90mm would be ideal. Ill let you know how i get on & if i need any,thanks again.
Anglia68 Posted January 5, 2007 Report Posted January 5, 2007 A better option although a bit pricey is a set of ARP head studs.
LEONMEX Posted January 5, 2007 Author Report Posted January 5, 2007 Go on,how much for the head studs?
LEONMEX Posted January 5, 2007 Author Report Posted January 5, 2007 Just been on the burton site & 117quid for the ARP studs & 45quid for another oversize head gasket Gota be done i suppose.
LEONMEX Posted January 6, 2007 Author Report Posted January 6, 2007 Spoke to a few engine builders today & HT racing & a few others cut there bolts down (with a hacksaw) a fit them as they are,so cut 4mm off each bolt & its sorted. How easy was that lol?
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now