Jump to content

Recommended Posts

Posted

Kev [KJ1320] and Phil [o.h.c ] have been busy :lol:

 

Thanks to Phil for all of his hard work and cardboard cutting skills :lol: :lol:

 

 

 

They have spent all weekend locked in the garage :lol:

 

Here are a few pics of what they have been up to :wink:

 

 

 

Ready :shock:

 

Cutting out the floor for the new axle and ladder bar setup

 

2008_0628ebay0001.jpg

 

 

2008_0628ebay0003.jpg

 

2008_0628ebay0006.jpg

 

 

2008_0628ebay0007.jpg

 

 

 

Bit drastic with weight saving :lol:

 

2008_0628ebay0008.jpg

 

All the excess weight removed and cleaned up ready for the refit :thumbsup:

2008_0706ebay0014.jpg

 

Making and fitting all the brackets on the new axle

 

2008_0706ebay0016.jpg

 

2008_0706ebay0020.jpg:lol:

Posted

BTW, would someone mind explaining to me what a 'ladder bar' set up is all about and why it's done. Ta muchly :mrgreen:

 

Kevs laughing because he does not know either :wink::lol:

Posted

wow nice one boys!!

 

ladders are the ones that have a fixed rod top and bottom of the axel are they not? so effectivly killing axel tramp completly

 

then where they bolt to the car body you can move them up and down to angle the axel or something :?:?

 

no hang on it wouldnt angle the axel but changes how the forces react against the body of the car either lifting the fronts straight off the ground or burrying them into the tar

 

 

 

i could of course be talking absolute rubbish :wink:

Posted
ultimate axle :-D

 

mick rogers runs a ladder bar setup and youve seen how that goes :shock:

 

And Terry Davies (10secterry) 8)

also favoured by the Maltese boys m8 :wink:

Posted

the blue mk2?

 

also notice that his car looks impossible to keep straight :-D

 

sideways at 90mph in 3rd gear i think id brown my pants :lol:

Posted

Ladder bars where used to replace leaf springs so eliminating the spring tramp. the early ones and a lot of after market kits are designed to bolt into the front spring mount .. more advanced kits came with a front bar to fit inside the car and allow adjustment of where the front pick up is. The springs eyes mount tends to be below the floor, this gives squat, by placing the brackets above the floor, they could adjust teh height of the front pick up so that it converged at the Center of Gravity ( CofG) of the car, thus giving anti squat.

 

Anti squat puts more weight onto the back axle. If you imagine a squatting car, even with a wheel off the ground at the front you only have around 2/3rds of teh cars weight on the back axle, With Anti-squat you lift the car at its CofG and teh whole of the cars weight is transmitted to the back axle (torque reaction and leverage )

 

The Ladder bar is still not as accurate as the 4 bar, as it works on 1 point, so cant be adjusted to accuratly pick up on the CofG where as the separate arms of the 4 link can.

 

 

With the 4 link, the arms are adjusted so they converge on the CofG .. the top arm is pulling backwards and the bottom is pushing up as the torque tries to rotate the axle. this is what gives the lift.

Posted

:twisted::twisted::twisted::twisted::twisted:

 

what times you hoping with that then ?

 

and while your at it are you gona spce frame the rear end? or just leave it cuse a boot aint exactly heavy :lol:

 

 

Good luck :wink::thumbsup: cant wait to see it

Posted
:dope: If it gets any lighter m8, you'll have to put a pinto in it to anchor it down :lol::lol: Just don't park it outside on a windy day, it'll blow away :P

 

PMSL! M8 so what"YOU" are saying is pinto's are nothing but ballast! :lol::lol::lol:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...