so whos getting their bufty on

[Rick]

or just workin hard to be ready for cf show?

 

iv been rolling round on the floor all morning again checking everything is tight, lubed and ready for a long ride

 

 

just hope its not wet on the day

[Guest MK1gaz]

Mines in bits still as the fooooooookin useless tossers at the motor factors have sent the wrong rear wheel bearings 3 foooooookin times !!!!!!!!!

[Lukey]

Mines in bits still as the fooooooookin useless tossers at the motor factors have sent the wrong rear wheel bearings 3 foooooookin times !!!!!!!!!

 

Mine too, waitin for bits tomorrow, got to get 40 year old rusted on steering bits off & new fitted before 11am frisday when my re-mot is. AAARRRGGGHHH!!!!

[Vista]

Have RAC card, will travel

[johnny_h]

This week I will mostly be fettling.

[LEONMEX]

Mines in bits still as the fooooooookin useless tossers at the motor factors have sent the wrong rear wheel bearings 3 foooooookin times !!!!!!!!!

 

What do you need gaz atlas bearings for your shafts??

[crapichris]

Mines in bits still as the fooooooookin useless tossers at the motor factors have sent the wrong rear wheel bearings 3 foooooookin times !!!!!!!!!

_________________

Had the same problem last week. Did a service for the MOT last week and found the halfshaft bearing had let oil past it - all over the brakes. Eventually got hold of a bearing and someone to press the old one off.

Just been for the MOT and it passed - whoooooooppppeeeeeeeeee!

CU at SP.

[antz]

still got an engine in bits but im close.

 

i got friday off to do the bufty jobs

[Mad Mex]

Mines in bits still as the fooooooookin useless tossers at the motor factors have sent the wrong rear wheel bearings 3 foooooookin times !!!!!!!!!

 

feeling your pain gaz, motor factor sent me the wrong clutch kit, had to wait till today( usual bank holiday meltdown)got the right kit from a diff company, but the fooking release bearing is way to big, might aswell be for a friggin land rover!!!! gonna be a mad dash to the finish this week so much to do so little time

[kevmk2]

Burtons gave me some BRT bearings for my mates atlas axle on his mk2, they had some weird oil ring seal around them. Ron at HT's said they were shit, so took them back and got Q&H ones, much better

[Guest MK1gaz]

[mossy]

ive got to ...

 

paint and fill the floor

bolt in my rollcage

fill my petrol tank

 

 

And get lost trying to find the Pod!

[BaileyMex]

getting it ready for an MOT Thursday afternoon,

 

I think I'll re test it at the end of the summer to avoid last minuet panics again

[Guest MK1gaz]

What do you need gaz atlas bearings for your shafts??

Just normal escort/cortina etc english axle wheel bearings (so they fit inside the axle tubes !!!!!!!!! ) unlike the 3 sets the useless gits keep sending !!!!!!!! . My mates son went over into their stores and found ALL their stock of wheel bearings were the foooookin same EVEN though they are all in different part numbered boxes !!!!!!!!! . Cooooooooooooounts

[LEONMEX]

Gaz part number ABK050 (automotive bearings) or the equivelant in SKF as these won't have the crap oil rubber ring,make sure they do the bearings for the english not the salisbury that is also listed for escorts on the same year

[Guest MK1gaz]

Cheers Leon . Well lets hope they don't foook up again tomorrow or else i could be a spectator at Santa Pod (Give the other atmo "comfys" a chance !!!!!!!!! )

[Rick]

doh i gotta wait two weeks for my door cards so they wont be coming. damn you aldridge trimming and your super high prices

[KJ 1320]

Cars Ready

 

but still got the trailer to sort out