Jump to content

xflow or zetec  

46 members have voted

  1. 1. xflow or zetec

    • xflow
      32
    • zetec
      15


Recommended Posts

Posted

Hi i have an anglia 105 with standard 997 lump in it but i dont no what to put in it i dont want super fast power and i have to consider cost as the more it costs the longer i have to save and the longer i cant drive it what do u think

Posted

With a couple of hundred quid you could have it done with an xflow on sunday but its gonna be expensive to put a Zetec in there. Either way get some good brakes FIRST! And stick up some pics when you can.

Posted
Hi i have an anglia 105 with standard 997 lump in it but i dont no what to put in it i dont want super fast power and i have to consider cost as the more it costs the longer i have to save and the longer i cant drive it what do u think

I vote ZETEC but you have answered your own question there mate ("i dont want super fast power and i have to consider cost") so it looks like a cross flow! I Still say Zetec though :D

Posted
Hi i have an anglia 105 with standard 997 lump in it but i dont no what to put in it i dont want super fast power and i have to consider cost as the more it costs the longer i have to save and the longer i cant drive it what do u think

I vote ZETEC but you have answered your own question there mate ("i dont want super fast power and i have to consider cost") so it looks like a cross flow! I Still say Zetec though :D

you would say that cheers any way
Posted
With a couple of hundred quid you could have it done with an xflow on sunday but its gonna be expensive to put a Zetec in there. Either way get some good brakes FIRST! And stick up some pics when you can.
There are some pics in the resto section mate cheers
Posted

well mate x flow, easy 2 fit and a lot cheaper, buying the intial zetec mite seem the same price as an x flow, but it doesnt stop there as to do the job properly you will need to buy a milton worldcup x member, then the mounts from retro rord, water rail, water pump, and lots of other goodies (havent reallly gone into it myself) so yea id go 4 the x flow as a cheaper base for your modified anglia. mine has a pinto but tbh mate too heavy for an anglia and a bugger to get it to fit. so the x flow is defo the best allround choice.

Posted

I used to think like you fellas.....

 

I loved my old school Pre-Crossflow... had all the trick period tuning bits...

 

but when I had a auld fella in a Fiat Multipla blew my doors off I knew it was time to step it up a gear and now I've got the Zetec I just think why didnt I do this years ago...

 

 

They are just so the right engine for an Anglia.... some things are worth the wait....

Posted

What did you tell me at the Ace Neil????????

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Zetec's are the Future :wink:

 

I had a thought the other day actually. My mate has just stripped a Y reg Fiesta that had a 1.25 Zetec. I wondered if it was shorter than the bigger Zetecs as I would really like to keep the heater box. But, the exhaust is on the opposite side :(

 

Might still have to have a measure up though :wink:

Posted

X-flow is best for you :D , zetecs are too costly to get working in the car and go like an old donkey :queer:

Posted

I have always loved crossflows and i have built and modded many crossflows over the years but when i went to zetec id never go back yes there might be a bit of a out lay on bits at first but once bought if the engine blows up it will only cost you 150-200quid for another zetec that pushes out 130+ bhp and a shed load of torque from standerd and if you use a modded cvh inlet manifold and a degas carb and fiesta or escort hcs ignition system with only two wires to conect like mine used to run you will be suprised how well they go and it dont cost a fortune and they are very easy to work on to and i dont miss adjusting the tappets every two weeks.

Posted

mr zefect wrote:

I have always loved crossflows and i have built and modded many crossflows over the years but when i went to zetec id never go back yes there might be a bit of a out lay on bits at first but once bought if the engine blows up it will only cost you 150-200quid for another zetec that pushes out 130+ bhp and a shed load of torque from standerd and if you use a modded cvh inlet manifold and a degas carb and fiesta or escort hcs ignition system with only two wires to conect like mine used to run you will be suprised how well they go and it dont cost a fortune and they are very easy to work on to and i dont miss adjusting the tappets every two weeks.

 

second that !!! bring on the old skool drags and we will see who goes like an old donkey!!!

Posted

if cost is a factor then personally i dont like crossflow or zetec as if fitting twin carbs then you have to spend 2/300 quid on a peddle box. so if not looking for outright power then as already suggested pre cross flo, and that must be the easiest conversion. although i would say look to the future ..... duratec.

Posted
I used to think like you fellas.....

 

I loved my old school Pre-Crossflow... had all the trick period tuning bits...

 

but when I had a auld fella in a Fiat Multipla blew my doors off I knew it was time to step it up a gear and now I've got the Zetec I just think why didnt I do this years ago...

 

 

They are just so the right engine for an Anglia.... some things are worth the wait....

 

Have to agree with Neil boys, I have a xflow in mine but the money is being saved for the Zetec conversion...mmmmm :twisted:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...